B200 Price: What Moves the Cost of B200 GPUs
B200 price depends on term, node count, region and what the quote includes. Learn what moves B200 pricing, how to read a quote and how to compare offers.
Why there is no single B200 price
There is no single B200 price, because every quote bundles several separate choices. The hourly figure is only the most visible one.
Some providers quote per GPU hour and others per node hour. A B200 SXM node in Pacific's catalog carries eight GPUs, so convert every quote to the same unit before you put two side by side.
The status of the number matters too. Pacific shows preview rates for B200 SXM, and those rates stay indicative until Pacific confirms the allocation. A finance lead who copies a preview rate into a budget model and multiplies it across eight GPUs and a full quarter is planning on a figure nobody has confirmed.
For the factors that apply to every GPU type, read the guide to GPU cloud pricing cost drivers. This guide stays on B200.
What moves a B200 quote
Term length is the first lever on a B200 quote in Pacific's catalog. The B200 SXM listing shows on-demand plus reserved bands of 7-30, 31-90 and 91-180 days by request, and each longer band shows a lower preview rate.
Allocation size is the second. One-node and two-node sizes are rentable directly, and four-node and eight-node sizes go by request, so a team scaling from a two-node test to an eight-node training run moves from a self-serve rental into a reviewed request with its own confirmed quote.
Region is the third. Pacific lists Asia Pacific, North America and Europe for B200. Confirm the quote for the region you will actually run in, and do not assume a preview in one region carries over to another.
Then look at what the price carries. Each B200 node is a dedicated bare-metal Linux host with SSH, NVIDIA drivers and CUDA installed, InfiniBand interconnect and local NVMe erased when the resource ends. Idle time is the driver you control, because a reserved node that sits unused still bills.
How to read a B200 quote line by line
Read a B200 quote one line at a time before you compare totals. A good test is whether you can rebuild the total from the lines yourself.
Check the unit, the GPU count and the node count first, then the term band and the region. Next, find what the quote says about tenancy, interconnect, drivers and storage handling, since a node that arrives ready for your job saves setup hours that would otherwise sit on your bill. For provider selection, see how to evaluate B200 cloud rental providers.
Then check status. Pacific's review step revalidates capacity, the current quote and terms before you commit, and a paid order is not a ready resource. An infrastructure lead planning a launch window should ask when the node is handed over and when charges start, and get both answers in writing.
Missing lines are a finding. Ask for them.
Compare B200 and H200 on cost per finished job
The cheaper hourly GPU can still cost more per finished training run. The number that matters is what one completed job costs at confirmed rates.
B200 SXM in Pacific's catalog carries 180 GB per GPU and H200 SXM carries 141 GB, both at eight GPUs per node. More memory per GPU can mean fewer nodes or less sharding for the same model, but whether it shortens your job depends on your model, your batch size and your code.
Run the same job on both for a short, fixed window, record wall-clock time and node count, then multiply by each confirmed quote. An ML lead who does this once with a real checkpoint and real data has better proof for the budget meeting than any spec sheet can offer.
For the hardware tradeoffs, see H200 vs B200 for training and inference. For H200 quote inputs, see H200 pricing factors for reserved capacity. For a reserved-capacity view against the older generation, read this B200 vs H100 comparison for reserved capacity buyers.
When reserved terms beat on-demand
Reserved B200 terms pay off when your utilization stays high across the term. The risk you take on is paying for days you do not use.
In Pacific's catalog each longer reserved band shows a lower preview rate than the band before it and than on-demand. That only helps if your queue keeps the nodes busy.
Start narrow. Rent one node on demand through Pacific's GPU rental for a day or a week, measure real throughput and idle hours, then size the reservation from that proof.
A team with a steady fine-tuning pipeline that runs every night for three months is a good fit for a longer band. A team still choosing model sizes should stay on shorter terms until the workload settles.
Questions to ask before you commit
Ask the hard questions during review, before money moves, and get written answers. Each one closes a gap between the preview and the bill.
Ask whether the quote is confirmed or still a preview. Ask how many nodes are allocated, in which region and for which exact term band. Ask when handover happens, what state the node is in at handover, and what happens to local NVMe data when the term ends.
Ask what changes if you extend, shrink or move from two nodes to four, since that step crosses into a by-request size. A procurement lead who gets these answers before signing avoids reopening the budget halfway through a run. The step-by-step path is in the guide to renting B200 GPUs.
When reserved B300 fits a long program
A long, steady training program may fit a reserved B300 cluster better. That path trades self-serve speed for a reviewed, written offer.
Pacific's reserved B300 offer is a single-tenant bare-metal cluster. Its Pod 32 reference comprises 32 HGX B300 nodes with a dedicated, configurable fabric, backed by witnessed factory, site and integration acceptance evidence.
Configuration and delivery window are confirmed through a project review and written offer, and commercial terms are discussed privately on a qualified call. The deployment timeline is a target confirmed site by site, never a guaranteed date.
If your roadmap runs past the six-month ceiling of B200 rental durations and needs one fabric across many nodes, read about reserved B300 capacity before you lock a B200 plan. For a written reservation checklist, see how to reserve NVIDIA B300 GPUs.
How to get a current B200 quote from Pacific
The most direct route to a real B200 number is a review in the catalog. Preview rates give you a starting point, and review gives you the figure you can budget.
Open Pacific Compute, select B200 SXM, pick a size, a region and a term, then go to review. One-node and two-node sizes rent directly, and four-node and eight-node sizes and reserved bands go through a request.
Availability shown is recorded by Pacific and confirmed when an order is accepted. A finance lead who brings the reviewed quote, the measured job time and the planned term into one sheet has everything needed to compare offers on the same footing.
When you are ready, start a B200 quote in the Pacific catalog.